ELSTER PERFECTION - Online Auction Event

1) TRANSCOM CHIP CONVEYOR, SERIAL 92-950-B, WIDTH 10”, OVERALL WIDTH 19”, HEIGHT OF HORIZONTAL 16” LENGTH OF HORIZONTAL 84”, DUMP HEIGHT 48”

2) 400 AMP LINCOLN WELDING POWER SOURCE, SERIAL VA990907260, MOCEL CV400, 3 PHASE, 230/460 VOLT

3) 500 AMP LINCOLN WELDING POWER SOURCE, SERIAL V1941207355, MODEL PULSE POWER 500, 3 PHASE, 230/440 VOLT

4) 1/2 TON FREE STANDING JIB CRANE, HEIGHT UNDER BEAM 10’, LENGTH OF BEAM 10’, 1/2 TON BUDGIT CHAIN HOIST W/ PENDANT CONTROL

5) 1” PINES #5T VERTICAL BENDER, SERIAL 44362-01024, MODEL 5T, NEW 2001, CAPACITY 1” X .072” NON FERROUS TUBE, DIGITAL DIAL A BEND CONTROL

6) 2-1/2” TECHNO HORIZONTAL PIPE & TUBE BENDER WITH MANDRAL EXTRACTOR, SERIAL 50-2506, MODEL T 50, NEW 2006, PRESSURE DIE ASSIST, DIRECT ACTING PRESSURE CLAMP

7) BERNARD COOLER, SERIAL WL39153, MODEL 6500SS

8) SYNTRON VIBRATORY BOWL FEEDER, SERIAL 2314, MODEL BB20, 32” DIAMETER, 8” DEEP, 25” HIGH, CAST IRON BASE 20” HIGH

9) SYNTRON VIBRATORY BOWL FEEDER, MODEL BB20, 32” DIAMETER, 8” DEEP, 25” HIGH, CAST IRON BASE 20” HIGH

10) SYNTRON VIBRATORY BOWL FEEDER, MODEL BB20, 32” DIAMETER, 8” DEEP, 25” HIGH, CAST IRON BASE 20” HIGH

11) SYNTRON VIBRATORY BOWL FEEDER, MODEL BB20, 32” DIAMETER, 8” DEEP, 25” HIGH, CAST IRON BASE 20” HIGH

12) SYNTRON VIBRATORY BOWL FEEDER, MODEL BB20, 32” DIAMETER, 8” DEEP, 25” HIGH, FABRICATED BASE 29” HIGH

13) (NEW) SYNTRON BOWL, 32” DIAMETER, 8” DEEP

14) DORRINGER COLD CUT SAW, SERIAL 19002, MODEL D350, BLADE DIAMETER 12”, PNUMATIC CLAMPING, PNUMATIC BLADE FEED, MITER 45 DEGREE EITHER WAY

15) 22” X 64” TOOLMEX GAP BED ENGINE LATHE, SERIAL 2744, MODEL TUJ-50M, SWING IN GAP 32”, DIAMETER OF SPINDLE HOLE 3-1/2”, INCH AND METRIC THREADING, TAPPER, STEADY REST, HARD WAYS

16) 15”4-JAW LATHE CHUCK, D-11 BACK

17) ADRAIN QUICK CHANGE TOOL POST HOLDER, MODEL XA, 5 TOOL HOLDERS

18) (1) DEAD CENTER, (2) 1/8” TO 3/4” JACOBS DRILL CHUCK, MODEL 18N, #5MT

19) PASS

20) DRILL BITS

21) 8” LANDIS PIPE THREADER, DIE HEAD R-46230LL3, CAPACITY 4” TO 8”, CUTOFF SLIDE, CHAMFER , DUAL CHUCKS, COOLANT

21A) 6” LANDIS PIPE THREADER, DIE HEAD R-47031KK3, CAPACITY 2-1/2” TO 6” PIPE, CUT OFF SLIDE, CHAMFER TOOL, DOUBLE CHUCKS (TOLEDO OHIO LOCATION)

22) 4” DOUBLE SPINDLE LANDIS PIPE & BOLT THREADER, DIE HEADS F4500G61

23) 2” LANDIS #2CLAN DOUBLE SPINDLE AUTOMATIC NIPPLE THREADER, SERIAL 2CLAN264, TOOLED FOR 1-1/2”NIPPLES, DIE HEAD1-1/4 TO 1-1/2 LANCO, HEAD NUMBER 10T00001-933508

24) 2” LANDIS #2CLAN DOUBLE SPINDLE AUTOMATIC NIPPLE THREADER, SERIAL 2CLAN551, TOOLED FOR 1-1/4” NIPPLES, DIE HEADS10T-2026, 1-1/4 LANCO, L10T00001-205581, 1-1/4 TO 1-1/2 LANCO

25) 2” LANDIS #2CLAN DOUBLE SPINDLE AUTOMATIC NIPPLE THREADER, SERIAL 2CLAN100, DIE HEADS 10T00001-919788-3, 1-1/4 LANCO, 10T0035, 1-1/4 LANCO

26) 2” LANDIS #2CLAN DOUBLE SPINDLE AUTOMATIC NIPPLE THRAEDER, SERIAL 2CLAN79, TOOLED FOR 1-1/4” NIPPLES, DIE HEADS 10T-1536-012286, 1-1/4 LANCO, 10T00001-919788, 1-1/4 LANCO

27) 2” LANDIS #2CLAN DOUBLE SPINDLE AUTOMATIC NIPPLE THREADER, SERIAL 2CLAN-293, TOOLED FOR 1-1/2” NIPPLES, DIA HEADS L10T0001-205581, 1-1/4 TO 1-1/2 LANCO, L10T001-205581, 1-1/4 TO 1-1/2 LANCO

28) 1/2” AND 3/4” LANDIS DOUBLE SPINDLE PIPE & BOLT THREADER, FRONT DIE HEAD 4T899-052326, 1/2 LAN CO, READ HEAD 6T1373-060334, PNUMATIC CLAMPING, COOLANT

28A) 1” LANDIS DOUBLE SPINDLE PIPE & BOLT THREADER, SERIAL 1I458, LEAD SCREW, DIE HEADS 1 LANCO 8R3708, 1 LANCO 8R3454 (TOLEDO OHIO LOCATION)

29) 3/8” TO 7-1/2” CONTINENTAL PIPE CUTOFF, SERIAL 61-61212, MODEL 6A, PUNMATIC FEED, ELECTRIC FOOT TRIP

29A) 6” MODERN CUTOFF LATHE, SERIAL 6L6311, MODEL 6L, NEW 1985, 3 SLIDES, 30’ MAGAZINE FEED RACK, UNLOADER (TOLEDO OHIO LOCATION)

30) 3” MODERN CUTOFF LATHE WITH 20’ MAGAZINE FEED RACK, SERIAL 3LD3442, MODEL 3LD, NEW 1997, 2 SLIDE, ROLLER CUTTER ON FRONT SLIDE, CHAMFER TOOL ON REAR SLIDE, 8’ STOCK STOP, UNLOADER

31) 3” MODERN CUTOFF LATHE, SERIAL 3LD3375, MODEL 3LD, NEW 1988, 2 SLIDE, ROLLER CUTTER ON FRONT SLIDE, CHAMFER TOOL ON REAR SLIDE, 8’ STOCK STOP, UNLOADER

32) 4-1/2” BARDONS & OLIVER CUTOFF LATHE , SERIAL 19726, MODEL 34ACL, NEW 1992, 3 SLIDES, FRONT SLIDE ROLLER CUTTER, REAR SLID CHAMFER TOOL, THIRD TOP SLIDE, LOWER SLIDES FEED ARE SERVO CONTROLLED, MAGAZINE FEED RACK, 8’ STOCK STOP, UNLOADER

33) 4” BARDONS & OLIVER CUTOFF LATHE, MODEL 34, 8’ STOCK STOP, 2 SLIDES, UNLOADER, MAGAZZINE FEED RACK

34) 15’ BARDONS & OLIVER FEED STOCK RACK

35) MONARCH HYDRAULIC POWER UNIT, SERIAL F243125, MODEL DYNA PACK, T22F505F03G8-01, 10 HORSEPOWER

36) BELLOWS HYDRAULIC POWER UNIT, SERIAL 48-5-3, MODEL A30014075, 3 HORSEPOWER

37) MONARCH HYDRAULIC POWER UNIT, SERIAL 9705 8635, MODEL T-08-15-0-16-04-1-030507-16-1-3, 3 HORSEPOWER

38) VICKERS HYDRAAULIC POWER UNIT, 3 HORSEPOWER

39) SET OF 4 LANDIS CHASER HOLDERS FOR LH PIPE

40) SET OF 4 LANDIS CHASER HOLDERS FOR PIPE

41) SET OF 4 LANDIS CHASER HOLDERS FOR LH PIPE

42) SET OF 4 LANDIS CHASER HOLDERS, #SB60432

43) SET OF 4 LANDIS CHASER HOLDERS, #SB60432

44) SET OF 4 LANDIS CHASER HOLDERS, FOR PIPE

45) (LOT) LANDIS CHAMFERING TOOLS