المقص التربع الطاقة (بوصة)TOPTECH VSHS-8X3100

Ontario, كندا

نظرة عامة

علامة تجارية
موديل
VSHS-8X3100
بطاقة الهوية
368627
حالة
الجديد في المخزن
السنة
2015
الموقع
Ontario
كندا
عودة السياسة
60 يوم
رقم المخزن
10002
الوصف
1.Frame structure Designed under FARINA technology Full steel structure, stress released, with accuracy well kept. Main component is designed and Finite Element Analyzed through ANSYS software. Main frame composes of uprights, working table, holding-down beam and oil tank. Ball transporter and supporting bar and squaring arm are fixed on working table. 2.Upper blade beam and blades Guillotine type blade beam, with rake angle adjustable The rake angle could be motorized adjusted by press button according to material and thickness. When shearing thin thickness sheet, the rake angle could be reduced, thus the distortion of the product and the burr could be minimized. Exchangeable Rectangle blade, with 4 cutting edges available. Blade material 6CrW2Si with hardness HRC53-60, with quality shearing result and long life. 3. Shearing length/stroke adjustment The shearing stroke could be adjusted through knob to the length of the product. Thus efficiency could be improved. 4. Cutting beam guiding and blade clearance The cutting beam is guided between roller guides. At the rear of the cutting beam there are two sets of upper and lower roller guides located at each end of the beam. Two spring-loaded rollers located at the front of the shear apply pressure to the cutting beam, forcing it against the back roller guides. The bearings of the upper roller guides at the back of the cutting beam are mounted on an eccentric shaft. Rotating this shaft causes the cutting beam to tilt, thus providing proper blade clearance to the shearing blades. The upper cutting beam inclined forward, with high section-cutting quality on the product. The blades clearance could be adjusted manually through hand-wheel according to material and thickness. Since the blade clearance is 0.1 to 2.5 mm 5. Hydraulic system SMAC special hydraulic unit for heavy type shear is adopted. Hydraulic control components is from YUKEN Japan (or HYDAC, Germany) With in-series cylinders to achieve good synchronization. The sheet is pressed by hold-down before shearing and during shearing for safety and reliability. One-time machining on CNC lathe for cylinder body and piston rod. Horning for inner surface of cylinder, vibration super-fine machining on the outer surface of the piston rod. Oil seals from NOK, Japan (or Merkel, Germany) with low wear and tear, no oil leakage. High-pressure internal gear pump, with reliability and low noise. Over-load protection for hydraulic system 6. Electrical system Movable remote operation station with emergency stop. Main electrical components(contactor, button and switch) adopt product from TELEMECANIQUE from France. Requirement on working condition: Working temperature: -10 to 47 Power supply: 380V±5%, 50HZ, 3 Phase 7. Shadow line lighting It is clear with shadow line lighting for a close and accurate view of the cutting line. 8 Motorized Back gauge The back gauge is driven by lead screw and normal motor. With electrical display, with stroke 750mm as standard and option to 1000mm. 9. Safety device Fence guard and protection switch for preventing finger being cut. Movable remote foot pedal with emergency stop
المواصفات
تحويل المواصفات للمتري
أقصى سمك0.3"
طول بليد12'
HYD / الميكانيكيةHyd
مقياس خلفى30"
القدرة15 hp
SPM 8 strokes/min.
الأبعاد154"*70"*83"
الوزن6100KGS

ورقة المواصفات

1 Cutting plate thickness 8 mm 2 Cutting plate width 3100 mm 3 Back gauge range 750 mm 4 Cutting angle 0.5~2.5 ° 5 Throat depth 70 mm 6 Main motor power 11 kW 7 Machine weight 6100 kg
عن البائع
الثمن

رؤية المزيد من العقارات المعروضة من هذا النوع

thumb

HTC 625-12SR

المقص التربع الطاقة (بوصة)

مستعملة - جيد | 1977 | Michigan, الولايات المتحدة الامريكية
thumb

WYSONG H-5012

المقص التربع الطاقة (بوصة)

مستعملة - جيد | 1995 | الولايات المتحدة الامريكية
thumb

CINCINNATI INC 4316

المقص التربع الطاقة (بوصة)

مستعملة - جيد | 1966 | Tennessee, الولايات المتحدة الامريكية
thumb

PULLMAX GST430

المقص التربع الطاقة (بوصة)

مستعملة - جيد | Illinois, الولايات المتحدة الامريكية
عرض جميع

رؤية المزيد من العقارات المعروضة لهذه العلامة التجارية

thumb

TOPTECH HPC-175/3100

الصحافة الفرامل

الجديد في المخزن | 2015 | Ontario, كندا
$75,000.00 USD
thumb

TOPTECH RD6016

تدريبات شعاعي

الجديد في المخزن | Ontario, كندا
$19,900.00 USD
thumb

TOPTECH TM6336

مطاحن الرأسي والأفقي

الجديد في المخزن | 2016 | Ontario, كندا
$13,000.00 USD
thumb

TOPTECH APL-110 (EDS-110)

مكابس مضغوطة الهواء

الجديد في المخزن | Ontario, كندا
$29,800.00 USD
عرض جميع