TECHNIDRILL .500-5-12-1بندقية المثاقب

بطاقة الهوية
422516
علامة تجارية
موديل
حالة
تستخدم - ممتاز
السنة
2010
الموقع
Michigan
الولايات المتحدة الامريكية
رقم المخزن
12710
صور ( 10 )

الممزيد حول هذا النموذج

لعرض مزيد من المعلومات على TECHNIDRILL .500-5-12-1 ، بما في ذلك المعلومات التجارية، والصور، والفيديو، وأكثر من ذلك، انقر هنا .

بطاقة الهوية
422516
علامة تجارية
موديل
حالة
تستخدم - ممتاز
السنة
2010
الموقع
Michigan
الولايات المتحدة الامريكية
رقم المخزن
12710

الوصف

Technidrill 500-5-12-1 PLC Gun Drill - NEVER USED!! w/Chip Conveyor

المواصفات

تحويل المواصفات للمتري
أقصى قطر للثقب
0.5 "
أقصى عمق للثقب
12 "
عامود الدوران#
1
الوزن
8,000
CNC تحكم
CNC (PanelMate)

Machine Features
• .500” Diameter maximum drilling capacity
* 0.150" Minimum Diameter drilling capacity
• 12” effective drill stroke with one optional whip guide installed.
• Fabricated steel base with 15” W X 20”L T-slotted work table with two centerline keyways and large coolant trough surrounding the base.
• Precision crossed roller linear guideways.
• Servo driven ballscrew providing feed rates from .100” to 24” per minute W/ 200 IPM retract.
• 3 HP spindle motor infinitely variable from 500 to 2,000 RPM.
• Precision spindle mounted in Class 7 bearings with standard gundrill socket. .750” X 2.750 deep with lock-screws for tool holding.
• Rotary coolant unions mounted to the rear of each spindle.
• Chipbox with bushing plate, coolant, and chip chute directing coolant and chips to the coolant system recovery area.
• Permanently grease lubricated spindles.

Coolant Filtration System Model 5-200-10

• 200 gallon coolant reservoir with two separate reservoirs, one for contaminated return coolant and one for clean filtered coolant.
• One 5-micron & one 10-micron filter with pressure switch to indicate when to change filters.
• One 5 HP, 10 GPM, (8 GPM @ 1000 PSI) High-pressure coolant pump with pressure switch to indicate loss of pressure.
• Water heat exchanger (Water supply required) or Air heat exchanger are standard.
• A chip basket with rough filter is installed in the return area of the coolant system.

Electrical System

• Consisting of a Nema 12 enclosure housing all motor starters, fuses, and disconnect.
• A touch screen operator station. (Cutler Hammer)
• Digital display of RPM
• Drilling depths are programmable.
• RPM and feed rates are programmable.
• Maximum travel limit switches to prevent over travel.
• Machine control, Allen Bradley SLC-500 series programmable control
• Automatic controls provide for detection of loss of coolant pressure, air pressure, clogged filters and includes diagnostic screens.
• Tool load monitoring via spindle load-meter.
• Allen Bradley AC servo feed drive system.
• ABB variable speed frequency inverter spindle drive
• Power requirements 460V 3PH 60HZ

Machine footprint 8’ X 11’
Shipping weight 8,000 Lbs

عن البائع

معلومات وجهة نظر الشركة