راقب

الفجوة الإطار (OBS) مكابسSANGIACOMO T-75

Ohio, الولايات المتحدة الامريكية

نظرة عامة

علامة تجارية
موديل
بطاقة الهوية
433224
حالة
تستخدم - ممتاز
السنة
2013
الموقع
Ohio
الولايات المتحدة الامريكية
عودة السياسة
كما هو
الوصف
2013 Flywheel eccentric press, Sangiacomo mod. T-75 CE Force capacity: 750 [kN] excellent condition
المواصفات
تحويل المواصفات للمتري
حمولة75 T
ارتفاع الغلق17"
القدرة10.1 hp
عرض الفراش20"
طول الفراش31"
SPM 140 strokes/min.
كلاتش هوائى (نعم/لاyes
الأبعادWidth 70 “ - Depth 60 “ - Height 110 “
الوزن11,500 lbs

ورقة المواصفات

1(one) Flywheel eccentric press, Sangiacomo mod. T-75 CE new year 2013 - Force capacity: 750 [kN] STRUCTURE - Electrical welded Fe 430 steel, with thermal distension treatment. - C-frame depth: 10 inch - Front gap between uprights: 14 “ - Distance between work table and ram (measured at the upper dead point with maximum stroke and ram regulation up): 17 “. WORK TABLE - Width 31.5 “ - Deep 20 “ - Diagonal T-slots for Ø0.6 “ T-slot nuts. - Central hole for discharging: Ø 180 with opening Ø 210 deep 0.86 “. BOLSTER PLATE - Width 31 “ - Deep 20 “. - Thickness 2.5 “ and T-slots like on the work table RAM DRIVEN BY 4 GUIDES WITH 6 SLIDING SURFACES: - n. 2 to the front at 45° - n. 4 to the back at 90° - Distance between guides: 16 x 11 “. - Spigot lock hole: Ø 2” H7 x 3.4 “. - Additional Ø 0.86” axial holes for fixing tool. Distance:0.62 “. - Ram surface 0.86 x 0.6 “. - n. 2 longitudinal and n.2 frontal T-slots for Ø 0.62 “ T-slot nuts. - Extraction bar system with an adjusting stroke up to 1”. - Hydraulic overload system with stop machine signal. - Ball regulation ring nut for clearance recovery between round headed brass and ram ball screw. - Designed to permit oil recovery and recycling. - Balancing cylinders for relieving masses during the alternating movement. CONNECTING ROD - With B14 brass diametrically divided. - Lengthening up to 2.8 “ by using a wrench bolt disk, with a mechanical arrest system to the maximum length. - Spherical connection system between connecting rod and ram. - Tangential brass locking gibs for blocking ram screw regulation. HYDRAULIC OVERLOAD - Automatic oil pressure release - Automatic reset of the working pressure - Situated below the connecting rod, preserves the ram from blocking and protects the machine from overload. (with release system) ECCENTRIC SHAFT - Made of Ni Cr Mo forged steel, drained, chromed and rectified; it rolls on B14 brasses with oil retainer rings. - Changing stroke system designed with frontal teeth. - Small eccentric shaft whereby opening the changing stroke system - Available strokes: 14 – 35 – 57 – 77 – 95 – 111 – 123 – 132 – 138 – 140. CLUTCH-BRAKE UNIT combined, electro-pneumatic action with extremely fast stopping time. - Air consumption 5,5 bar. - Frictional material without asbestos on thickened and interchangeable sections. - Rotating coupling on ball bearings. TWO-ELEMENT SOLENOID VALVE with cyclical control of the pressure inside two valves, supplied with excellent silencer. CADENCE: 120 stroke/min in continuous cycle 30 friction insertions/minute in single stroke. ELECTRICAL CONTROL PANEL - Programmable logic PLC It includes the following working functions: - inching, by two-hand control - single stroke, by two-hand control - continuous cycle, by two-hand control - single stroke with foot pedal - continuous cycle, start by pedal and stop by pedal at the T.D.C. - continuous cycle, start by pedal and stop by push-button at the T.D.C. - single stroke for closed dies, start by pedal - continuous cycle for closed dies, start by pedal and stop by pedal at the T.D.C. - reverse motor possible on inching mode. Every one of above selections automatically activates the related protection guards in order to guarantee the maximum safety level for the operator. The control panel is equipped with: - Total and partial stroke-counter and a hour-counter. - Memorization of main parameter of use of the press - Start-Timer function - Check-up continuous - Easy information regarding the status of the press - Speed adjustment (option) - Lubrication system adjustment It is possible to supply an interface connection for external device. MOTOR - Power: 7.5 kW - Tension: 220 V -60 Hz - Movement transmitted to the flywheel by using belts. - Motor bracket with belt stretcher AIR COMPRESSED FILTER-REGULATOR-LUBRICATOR 3/4” WAY WITH MANOMETER: - Minimum level pressure switch calibrated at 3 bar. LUBRICATION: - Centralized automatic with adjustable flow, with metering valves for lubricating gibs, connecting rod brass, eccentric shaft brasses. - Oil recover filtered for the recirculate. - Oil tank placed inside the structure doorway for an easy access. - Minimum level signal and oil pressure checking with eventual stop machine to the Top Dead Center WORK CONDITION: - Environmental temperature from 12°C to 38°C and relative humidity < 60% - Oil lubrication heating system can be supplied upon request. - Electrical cabinet air conditioner can be supplied upon request. PAINTINGS: - Emboss effect painting - Blue RAL5015, with dangerous items painted RAL2004 APPROXIMATE WEIGHT: 5200 kg. OVERALL DIMENSIONS: - Width 70 “ - Depth 60 “ - Height 110 “
عن البائع
الثمن
$10,001 - $50,000 USD

$10,001 - $50,000 USD

رؤية المزيد من العقارات المعروضة من هذا النوع

thumb

MAYPRESS MKN163/7

الفجوة الإطار (OBS) مكابس

Illinois, الولايات المتحدة الامريكية
thumb

DENISON T065LC204

الفجوة الإطار (OBS) مكابس

Illinois, الولايات المتحدة الامريكية
thumb

ROBERTS

الفجوة الإطار (OBS) مكابس

1985 | Illinois, الولايات المتحدة الامريكية
thumb

DENISON 100

الفجوة الإطار (OBS) مكابس

Illinois, الولايات المتحدة الامريكية
عرض جميع