راقب
راقب

مناشير الفرقة الأفقيSHARP SW-126

الولايات المتحدة الامريكية

نظرة عامة

علامة تجارية
موديل
بطاقة الهوية
447446
حالة
الجديد في المخزن
السنة
2020
الموقع
الولايات المتحدة الامريكية
رقم المخزن
1983
الوصف
12.6” X 12.6” Dual Column Hydraulically Powered Horizontal Bandsaw Incorporates a powerful 5 hp blade motor, 1 1/4” wide blade, independent control panel, and heavy-duty dual column design. These features create a very rigid, dynamically stable and productive machine. The heavy-duty dual columns keep the blade parallel to the material at all times creating consistent force throughout the entire cutting cycle, thereby increasing the cutting efficiency and extending blade life.
المواصفات
تحويل المواصفات للمتري
السعة المستطيلة (ارتفاع
12.6 "
السعة المستطيلة (عرض
12.6 "

ورقة المواصفات

Machine Structure:

Oversized hydraulic cylinder supports the rugged saw frame with heavy-duty universal ball joint accomplishing smooth & consistent downfeed through the entire cutting cycle.  Special wear resistant DU bushing works inside the precision bore solid cast hinge and ground pivot shaft to ensure durability and long useful life.

Cross Link is located on the top of the columns, connecting the two columns to form an archway design that gives it sound structural strength.

Hydraulic shuttle vise assembly, made of heavy-duty cast iron with replaceable hardened wear plates, rides on two large guide shafts that are capable of handling extreme loads.  Both shafts are ground and chrome plated for durability and smooth material feeding.

Blade Drive:

The gearbox is specially designed to accept high lateral pressure. Unlike conventional gearboxes, the Sharp design accepts more pressure during operation and will not create thermal distortion, providing long gearbox life under production conditions.

Inverter Blade Drive System allows infinitely variable blade speeds to be controlled by the operator from the control panel with turn of a knob. The system comes standard with LED readout for convenient and accurate setting of blade speed.

Blade Guidance & Lubrication System:

Carbide guides securely guide the blade during the cutting cycle. The carbide is relieved so that coolant can both cool and lubricate the blade during the cut.

The bearing guides eliminate blade stress by pre-aligning the blade before it enters the carbide guides. Two additional guides located on a central axis support the blade from the top, giving it extra penetrating force for faster cuts.

Automatic hydraulic blade tensioning device provides correct blade tensioning when the machine is turned on and will slightly release the tension when the machine is not running.  This extends blade life. The on-off hydraulic valve switch is an added feature making blade change quicker and easier

Integral coolant system. Coolant is supplied at four critical points: exit & entry of blade through blade guides, middle of cut via adjustable flex hose, and blade cleaning brush.

Synchronized power driven blade brush effectively cleans chips from blade to extend blade life.

Control & Automation:

The operator’s control station ergonomically located on the front side of the saw is convenient and user friendly. All operator controls are positioned on the top of the control box and clearly labeled for ease of operation. The electrical components are located inside the control box with the main lockout disconnect on the front of the control box for safety and easy maintenance.

Front mounted digital length counter, which provides accurate and easy length setups in increments of 0.05mm.

LED digital blade speed monitor is conveniently located on the operator’s counsel

Precision feed pressure & feed rate dual valve system for optimal cutting performance in any material.

PLC controls the function of hydraulic and electric system

Switch for selection of bundle or single cutting modes

Automatic work height selector and air gap eliminator positions the saw frame to a safe clearance above the workpiece, so that the next piece can be positioned without damaging the blade. After feeding, the saw head will descend quickly to within approximately 3 mm of work piece, where it proceeds at the predetermined cutting rates.

Preset work piece counter with automatic shutoff sensor for out of stock

Material Clamping & Feeding:

Split vise jaws on the front machine vise are standard. The split front vise will hold the work piece on both sides of the blade for a burr-free cut. This system also features automatic feeding of material down to a remnant length of 50mm.

Ductile cast iron vises with replaceable hardened wear plates.

PLC Controlled Multiple indexing for long cutting lengths of up to 3600mm maximum length.

One set of vertical alignment rollers, which is convenient for bundle cutting and positioning bar stock, is standard and is located on the machine base.

Multiple horizontal rollers located on the entry side of the saw to facilitate smooth material feeding.

Discharge Table with built–in coolant return adequately supports cut-off stock and provides coolant savings in the long run.

Safety:

Proximity switches sense both blade slippage and blade breakage and will automatically shut off the machine if either of these conditions should occur.

All blade covers and guarding on the saw are painted Alert Orange to increase safety alertness.

All exposed electric wiring and hydraulic circuit are protected by conduits.

 

MACHINE SPECIFICATIONS

MAXIMUM CUTTING
CAPACITY

Round

12.6”

Square

12.6” x 12.6”

Rectangle

12.6” x 15”

Bundle

Width: 190 – 300 mm
Height: 70 - 140 mm

SAW BLADE

Speed

66 – 328 FPM
(Inverter driven variable speed)

Size

167” x 1.33” x 0.04”

Tension

Hydraulic Controlled

Guide

Tungsten Carbide Blade Guide

Cleaning

Wire Brush

MOTOR OUTPUT

Saw blade

5 HP

Hydraulic

1 HP

Coolant

1/8 HP (0.1 KW)

TANK CAPACITY

Hydraulic oil

25L

Coolant

45L

FEEDING

Mode

HYDRAULIC, Automatic

Length

Single Stroke: 15.9”
9 times: 141”

VISE CONTROL

Split front vise and hydraulic shuttle vise

NET / GROSS  WEIGHT

4400 LBS / 4840 LBS

FLOOR SPACE

79” x 79” x 59”

Standard Accessories:

Blade “clip” device eases blade changing when necessary by holding the blade on the band wheel during installation, making it very easy for one person to change the blade.

Adjustable fence to support bundled cut-off stock

Additional flushing hose for cleaning

Built in work light

Bi-metal saw blade

Tool Box with tools, leveling pads, and an additional wire brush

Operation & parts manual

 

عن البائع
الثمن

رؤية المزيد من العقارات المعروضة من هذا النوع

thumb

COSEN MH-1016JA

مناشير الفرقة الأفقي

الجديد في المخزن | North Carolina, الولايات المتحدة الامريكية
$4,295.00 USD
thumb

COSEN SH-460M

مناشير الفرقة الأفقي

الجديد في المخزن | North Carolina, الولايات المتحدة الامريكية
$7,695.00 USD
thumb

COSEN SH-500M

مناشير الفرقة الأفقي

الجديد في المخزن | North Carolina, الولايات المتحدة الامريكية
$11,895.00 USD
thumb

SHARP 350SDV

مناشير الفرقة الأفقي

الجديد في المخزن | كندا
عرض جميع

رؤية المزيد من العقارات المعروضة لهذه العلامة التجارية

thumb

SHARP SV-4328SX

مراكز التجهيز العمودي

الجديد في المخزن | California, الولايات المتحدة الامريكية
thumb

SHARP LMV

مطاحن العمودي

الجديد في المخزن | California, الولايات المتحدة الامريكية
thumb

SHARP 1118H

مخارط الدقة

الجديد في المخزن | California, الولايات المتحدة الامريكية
thumb

SHARP 2680B

مخارط المحرك

الجديد في المخزن | California, الولايات المتحدة الامريكية
عرض جميع