راقب
راقب

مناشير الفرقة الأفقيSHARP SW-100A

الولايات المتحدة الامريكية

نظرة عامة

علامة تجارية
موديل
بطاقة الهوية
447448
حالة
الجديد في المخزن
السنة
2020
الموقع
الولايات المتحدة الامريكية
رقم المخزن
1982
الوصف
10” X 11” Capacity Pivot Style Automatic Horizontal Bandsaw with LED Digital Blade Speed Monitor, Programmable Shuttle Vise, Bundle Clamping, Automatic Work Height Selector and Integrated Flood Coolant System.
المواصفات
تحويل المواصفات للمتري
السعة المستطيلة (ارتفاع10"
السعة المستطيلة (عرض11"

ورقة المواصفات

Sharp's SW-100 A is a high production machine, which incorporates a massive base, sturdy saw frame, with an extremely heavy-duty gearbox, a 3HP drive motor, and a user-friendly control panel for ease of operation. MACHINE FEATURES Machine Structure: ■ Oversized hydraulic cylinder supports the rugged saw frame with heavy-duty universal ball joint accomplishing smooth & consistent downfeed through the entire cutting cycle.  Special wear resistant DU bushing works inside the precision bore solid cast hinge and ground pivot shaft to ensure durability and long useful life. ■ The saw head adopts a back tilt design which allows the blade to twist less than traditional bandsaws between the wheel and blade guide; thereby putting less stress on the blade, insuring longer life. ■ Hydraulic shuttle vise assembly, made of heavy-duty cast iron with replaceable hardened wear plates, rides on two large guide shafts, capable of extreme load support.  Both shafts are ground and chrome plated for durability and smooth material feeding. Blade Drive: ■ The gearbox is specially designed to accept high lateral pressure. Unlike conventional gearboxes, the design accepts more pressure during operation and will not create thermal distortion, providing long gearbox life under production conditions. ■ Inverter Blade Drive System allows infinitely variable blade speeds to be controlled by the operator from the control panel with turn of a knob. The system comes standard with LED readout for convenient and accurate setting of blade speed. Blade Guidance & Lubrication System: ■ Carbide guides securely guide the blade during the cutting cycle. The carbide is relieved so that coolant can both cool and lubricate the blade during the cut. ■ The bearing guides eliminate blade stress by pre-aligning the blade before it enters the carbide guides. Two additional guides located on a central axis support the blade from the top, giving it extra penetrating force for faster cuts. ■ Automatic hydraulic blade tensioning device provides correct blade tensioning when the machine is turned on and will slightly release the tension when the machine is not running.  This extends blade life. The on-off hydraulic valve switch is an added feature making blade change quicker and easier ■ Integral coolant system. Coolant is supplied at four critical points: exit & entry of blade through blade guides, middle of cut via adjustable flex hose, and blade cleaning brush. ■ Synchronized power driven blade brush effectively cleans chips from blade to extend blade life. Control & Automation: ■ Front mounted digital length counter, which provides accurate and easy length setups in increments of 0.05mm. ■ LED digital blade speed monitor is conveniently located on the operator’s counsel ■ Precision feed pressure & feed rate dual valve system for optimal cutting performance in any material. ■ PLC controls the function of hydraulic and electric system ■ Switch for selection of bundle or single cutting modes ■ Automatic work height selector and air gap eliminator positions the saw frame to a safe clearance above the workpiece, so that the next piece can be positioned without damaging the blade. After feeding, the saw head will descend quickly to within approximately 3mm of work piece, where it proceeds at the predetermined cutting rates. ■ Preset work piece counter with automatic shutoff sensor for out of stock Material Clamping & Feeding: ■ Split vise jaws on the front machine vise are standard. The split front vise will hold the workpiece on both sides of the blade for a burr-free cut. This system also features automatic feeding of material down to a remnant length of 50mm. ■ Hydraulic front and rear vises enable clamping and unclamping of any material from the operator’s control station. ■ Ductile cast iron vises with replaceable hardened wear plates. ■ PLC Controlled Multiple indexing for long cutting lengths of up to 3600mm maximum length. ■ One set of vertical alignment rollers, which is convenient for bundle cutting and positioning bar stock, is standard and is located on the machine base. ■ Multiple horizontal rollers located on the entry side of the saw to facilitate smooth material feeding. ■ Discharge Table with built–in coolant return adequately supports cut-off stock and provides coolant savings in the long run. Safety: ■ Proximity switches sense both blade slippage and blade breakage and will automatically shut off the machine if either of these conditions should occur. ■ All blade covers and guarding on the saw are painted Alert Orange to increase safety alertness. ■ Interlock design in electrical and hydraulic system prevents the saw from accidental start All machines ■ Conduit protects all exposed electric wiring and hydraulic circuits. MACHINE SPECIFICATIONS Maximum Cutting Capacity: Round Square Rectangle Bundle (w/opt 250 top clamps) O    9.84”     9.84” x 9.84”  9.84” x 11” (W) 6.1” - 7.87” (H) 1.0969” X - 4.724”       Blade: Speed Variable Size 65 – 328 Feet P/min 138” x 1.34” x 0.043”       Motor: Saw Blade Hydraulic Coolant 3 HP 1 HP 1/8 HP       Automatic Material Feed System: Single Index Stroke Multiple Stroke Indexing 0 to 15.75” 0 to 141.73” (1 to 9 indexes)       Weight   3,086 LBS Floor Space (L x W x H)   75” x 73” x 62” Standard Accessories: ■ Blade “clip” device eases blade changing when necessary by holding the blade on the band wheel during installation, making it very easy for one person to change the blade. ■ Adjustable fence to support bundled cut-off stock ■ Additional flushing hose for cleaning ■ Built in work light ■ Bi-metal saw blade ■ Tool Box with tools, leveling pads, and an additional wire brush ■ Operation & parts manual
عن البائع
الثمن

رؤية المزيد من العقارات المعروضة من هذا النوع

thumb

COSEN MH-1016JA

مناشير الفرقة الأفقي

الجديد في المخزن | North Carolina, الولايات المتحدة الامريكية
$4,295.00 USD
thumb

COSEN SH-460M

مناشير الفرقة الأفقي

الجديد في المخزن | North Carolina, الولايات المتحدة الامريكية
$7,695.00 USD
thumb

COSEN SH-500M

مناشير الفرقة الأفقي

الجديد في المخزن | North Carolina, الولايات المتحدة الامريكية
$11,895.00 USD
thumb

SHARP 350SDV

مناشير الفرقة الأفقي

الجديد في المخزن | كندا
عرض جميع

رؤية المزيد من العقارات المعروضة لهذه العلامة التجارية

thumb

SHARP SV-4328SX

مراكز التجهيز العمودي

الجديد في المخزن | California, الولايات المتحدة الامريكية
thumb

SHARP LMV

مطاحن العمودي

الجديد في المخزن | California, الولايات المتحدة الامريكية
thumb

SHARP 1118H

مخارط الدقة

الجديد في المخزن | California, الولايات المتحدة الامريكية
thumb

SHARP 2680B

مخارط المحرك

الجديد في المخزن | California, الولايات المتحدة الامريكية
عرض جميع