لف أسلاكKINEFAC

Connecticut, الولايات المتحدة الامريكية

نظرة عامة

علامة تجارية
بطاقة الهوية
466341
النوع
حالة
مستعملة - جيد
الموقع
Connecticut
الولايات المتحدة الامريكية
رقم المخزن
5519
الوصف
Kinefac CNC Ring Coiler/Continuous Kine-Coiler Sleeper Continuous Ring Coiler (#5519)
المواصفات

ورقة المواصفات

CNC Ring Coiler/Kine-Coiler

Sleeper/Kinefac

ALMOST NEW-Very Few Hours!

Continuous Ring Coiler

VERY GOOD CONDITION!

Model #915

CNC Ring Coiler/Continuous Coiler

Very Few Hours!

Video Available

 

WIRE GAUGE:

Wire diameter .005 inches to .018 inches with index to 3.

WIRE MATERIAL:

Capable of making springs in stainless steel, music wire, phosphor bronze, beryllium copper, platinum alloys, etc.

Shaped wire with a cross sectional area up to that of .018 inch diameter round wire.

COIL CHARACTERISTICS:

Maximum compression spring OD of .375 inches.

Compression springs with closed ends, closed ends and center, taper, barrel, closed ends with cones.

Continuous closed, open or variable pitch coils of an unlimited length.

Coiler available in either left hand or right hand versions.

FEED ROLLS:

Feed rolls 1.200 inch diameter.

Both feed rolls driven.

Upper feed roll smooth.

Lower feed roll with multiple grooves covering the full wire range .005 inches to .018 inches.

Lower feed roll axially adjustable by # 3-56 adjustment screw for wire size alignment.

Upper feed roll axially adjustable for wear compensation.

Upper feed roll pressure precisely adjustable by calibrated spring unit.

Upper feed roll assembly swings out of the way for visibility of wire line alignment.

Upper and lower feed rolls of carbide.

Lower feed roll direct servo driven.

Minimum wire feed increment .0003 inch.

Maximum wire feed rate 3000 inches per minute.

DIAMETER AXIS:
Coiling point tool holder directly driven by servo mounted actuation cam.

Coiling point CNC radially positionable in .00004 inch increments.

Coiling point laterally positionable by differential translator in .000003 inch increments.

Coiling point vertically adjustable by micrometer in .0005 inch increments.

Coiling point actuation axis can be rotated +30 degrees to -35 degrees with respect to the wire line for two point coiling or other special coiling applications.

Diameter slide has anti-friction linear bearings.

Diameter slide is spring loaded against cam surface.

Diameter slide travel .200 inch.

Coiling point clamp is "V" type to allow use of either preset, square shank coiling points or round shank coiling points.

PITCH AXIS:

Pitch tool holder directly driven by servo mounted actuation cam.

Pitch tool CNC positionable axially to .00005 inch increments.

Pitch slide has anti-friction linear bearings.

Pitch slide spring loaded against cam surface.

Standard pitch tool stem accepts .032 inch diameter carbide point.

Two pitch tool locations in tool holder to provide coil clearance options.

CNC pitch control system adapted for free length gage feed back.

CUT AXIS:

Cutting tool shaft directly driven by servo mounted actuation cam.

Cutting tool CNC radially positionable for cut and retract positions.

Cutting tool laterally positionable by micrometer in .000025 inch
increments.

Cut actuation arm is spring loaded against cam surface.

Cutting tool screw clamped from front with two mounting positions for
optimal cutting angle.

TOOL HOLDER and ARBOR ADJUSTMENT (CHUCK):

Tool holder is non-rotatable, hardened steel and removable with stable, locking configuration for repeatability of location.

Tool holder contains .125 inch by .187 inch arbor mounting hole. Round .125 inch diameter arbor mounting hole is available as an option.

Tool holder has independent arbor clamping by cam device accessible from the front of the machine using a #3-56 screw.

Tool holder contains precision bearing bore for pitch tool stem

Pitch tool holder contains final guide mounting reference surfaces and clamp screw Boles.

Arbor is axially adjusted by positioning and ejection rod.

Positioning and ejection rod is axially adjusted by #3-56 screw from front of machine.

Arbor can be removed by positioning and ejection rod without loss of axial position.

GENERAL MACHINE CHARACTERISTICS:

Arbor, coiling point, pitch tool and cutter independently removable.

Minimum number of fastener sizes.

All fasteners used to mount tooling are #3-56 socket head cap screws.

Wire line adjustable from 40 inch to 48 inch from floor.

Machine body is heat-treated steel.

Machine provided with 30 inch wide by 60 inch long table for customer determined mounting of machine controls and related equipment.

DRIVES, CONTROLS and SOFTWARE:

Feed, diameter, pitch and cut servo drive motors run at 12000 counts/turn.

Rotational accuracy Ìá/- .03 degree.

Motors driven through Galli motion control card.

Controlled by standard PC.

PC input by standard keyboard or mouse.

Screen display on standard 17-inch monitor.

Software is Visual Basic with modified G-Code.

HPG provided for independent operation of each axis or simultaneous operation of axis in manual operation mode.

Multiple program storage.

Control program compatible with length correction through pitch control correction feedback from free length gage

 

TOOL LIST:

Feed Wheels:

.018‰Û groove

.020‰Û groove

Capability - .017‰Û - .020‰Û wire diameter

Quills:

Preliminary .018 and .020 groove

Intermediate .018 and .020 groove

Final .018 and .020 groove

Coiling Points:

2 Sets - .018‰Û square with titanium nitrate impregnated tips.

1 Set - .018‰Û round with diamond tips

1 Set - .018‰Û round with carbide tips

1 Set - .020‰Û round with carbide tips

1 - External face cutting system for coil sheath (guide wire) production.

Includes cutters

1 - Proximity switch

1 - Work light

There will be a Skidding/Loading Fee at the time of sale.

 

Job it was purchased for was not received so the machine did not get put into production

Machine is LIKE NEW!

 

 

 

 

عن البائع
الثمن

رؤية المزيد من العقارات المعروضة من هذا النوع

thumb

WAFIOS FTU-0

لف أسلاك

مستعملة - جيد | Pennsylvania, الولايات المتحدة الامريكية

رؤية المزيد من العقارات المعروضة لهذه العلامة التجارية

thumb

KINEFAC TD-21 KINE-TURN

مخارط CNC

2006 | Michigan, الولايات المتحدة الامريكية
thumb

KINEFAC MC-5/10

درفلة قلاووظ

الولايات المتحدة الامريكية
thumb

KINEFAC MC-25

درفلة قلاووظ

مستعملة - جيد | الولايات المتحدة الامريكية