راقب

آلات وضع العلاماتMATTHEWS 2091

Illinois, الولايات المتحدة الامريكية

نظرة عامة

علامة تجارية
موديل
بطاقة الهوية
472654
الموقع
Illinois
الولايات المتحدة الامريكية
رقم المخزن
48429
الوصف
Matthews Indent-A-Mark Model 2091, 2-1/2 ton,Roll type,6"cross-slide str.'89
المواصفات
تحويل المواصفات للمتري
وسم المنطقة8 "
وسم المنطقة24 "

ورقة المواصفات

Serial No. L-84 New - 1989 SPECIFICATIONS: Marking Force.......................700 lbf to 5,000 lbf (317.5 to 2,268 kgf) Cross Slide.....................................0.5" to 6" (12.7 to 152.4 mm) Ram Stroke.....................................0.125" to 1" (3.18 to 25.4 mm) Throat Height Ram Down/Head Down.............................................0.5" (12.7 mm) Ram Up/Head Up.................................................18" (457.2 mm) Throat Width................................13.5" (342.9 mm) Between Uprights Marking Table Size......................24" Wide x 8" Deep (609.6 x 203.2 mm) Marking Table Bolt Pattern.........................4" x 6" (101.6 x 152.4 mm) Cycle Rate..............43 CPM at a 1" (25.4 mm) Stroke & 700 lbf (317.5 kgf) 35 CPM at a 1" (25.4 mm) Stroke & 5,000 lbf (2,267.96 kgf) Electrical...........................................220/440 VAC, 3 PH, 60 Hz Motor.....................................1.5 HP, 1,725 RPM (1.52 HP, Metric) Pump.......................................................1.5 GPM (5.68 LPM) Fluid Reservoir........................................5 Gallon (18.93 Liter) Sequence of Operation: The desired legend, composed of both steel type and logodies, is set in the roll style type holders which are mounted in two Versa-dex carriages. These carriages are positioned on a special dove-tail mounting bar corresponding to the diameter of the piston and secured in place. The mounting bar is then attached to the ram assembly. After adjusting the marking force to the required level, the operator places the part into the fixture to accurately position and securely hold it during the marking cycle. Depressing the dual palm buttons activates the marking cycle. When activated, the ram travels vertically downward to the part. As the leading edge of the first character in each line of the legend touches the part, the marking force required begins to develop and the leading edge is indented to the desired depth. When this occurs, the ram assembly traverses across the part to indent the rest of the legend. After the part is marked, the ram raises and the assembly slides back to the start position. EQUIPPED WITH: Indenting Ram Assembly Vertical Adjustment Columns Integrated Hydraulic Power Pack Operating Control Panel Dual Carriage Tooling Marking Table with V-block Fixture Miscellaneous Tooling, Characters *Preliminary Specifications Subject to Verification
عن البائع

رؤية المزيد من العقارات المعروضة من هذا النوع

thumb

EAGLE EA0-067

آلات وضع العلامات

Illinois, الولايات المتحدة الامريكية
thumb

PROPEN M7000 HANDHELD

آلات وضع العلامات

تستخدم - ممتاز | 2015 | Illinois, الولايات المتحدة الامريكية
thumb

TECHNOMARK MULTI-4

آلات وضع العلامات

الجديد في المخزن | Texas, الولايات المتحدة الامريكية
thumb

TECHNIFOR IMPACT P

آلات وضع العلامات

2019 | Illinois, الولايات المتحدة الامريكية
عرض جميع

رؤية المزيد من العقارات المعروضة لهذه العلامة التجارية

thumb

MATTHEWS MP-20

آلات وضع العلامات

Illinois, الولايات المتحدة الامريكية
thumb

MATTHEWS MP-21

آلات وضع العلامات

Illinois, الولايات المتحدة الامريكية
thumb

MATTHEWS MB-20

آلات وضع العلامات

Illinois, الولايات المتحدة الامريكية