DESCRIPTION / QUOTATION We offer, subject to prior sale: One (1) - Model No. 48-12 FELLOWS Vertical Gear Shaping Machine, suitable for the manufacture of internal and external spur gears, (as well as helical gears with proper guides), up to 48” (1219mm) pitch diameter, 12” (305mm) face-width, and 2 DP (module 12.7). Serial No. 35081 (New 1974) The machine corresponds to the attached copy of factory literature, featuring the following: EQUIPMENT / FEATURES: • straight spur guide for cutter-spindle • pneumatic assist for moving of work apron plus apron support • special 24” (609.6) height riser-block providing roughly 25.81” (655.6mm) total work-piece & fixture clearance height • dial set gear box providing 12 stroking speeds (from 12 to 190 S.P.M.) • twelve (12) different rotary feeds (from .0006 to .007 per inch of cutter P.D.) • 5” diameter heavy-duty, hollow cutter-spindle  • two (2) standard cutter adaptors • dial with adjustable trip dogs for depth feed control and number of cuts • work-spindle fast rotation for truing work • rapid traverse for cutter-saddle • operator’s pendant control • 48” diameter T-slotted work sub-table • power forced lubrication system to all elements  • self-contained coolant system for cutting oil • assortment of change gears (approx.35-gears) • full complement of electrics (motors/controls)(presently arranged for 3-phase 220/440 Volt, 60 Hz operation) • operator’s manual, parts list, wiring diagrams PRINCIPAL SPECIFICATIONS: Maximum pitch diameter...........................................48"(1219mm) Maximum diameter work-piece or fixture...........................54”(1372mm) Max. center distance between work-table and cutter-spindle centerline (external gear)....................................28.5”(723.9mm) Max. center distance between work-table and cutter-spindle centerline (internal gear)..................................21.25”(539.75mm) Maximum pitch spur........................................2 DP (module 12.7) Maximum pitch helical......................................3 DP (module 8.5) Maximum nominal face width internal/external......................12”(305mm) Maximum stroke length............................................13”(2870mm) Maximum helix angle (w/proper guides)............................45 degrees Max. distance work table surface to underside of cutter spindle in upper-most position.......................................25.81”(655.6mm) Cutter spindle taper bore......................................No. 18 Jarno Work spindle bore diameter.................................5.875”(149.225mm) Saddle back-off after completion of cut......................1.140”(28.96mm) Maximum weight face plate, fixture and part..............2,750 Lbs(1250 kGs) Cutter Spindle diameter............................................5”(127mm) Stroking speeds (12)..........................................12 to 190 SPM Machine dimensions...................92” x 76” x 141” (2337 x 1930 x 3581mm) Machine net weight, approx...........................22,000 lbs.(10,000 kGs) * * * * * For the machine professionally “reconditioned” o machine thoroughly cleaned o all worn and/or broken parts repaired or replaced o lubrication and electrical system reviewed o machine checked for proper function o machine prepped and painted per customer's specified paint scheme EXTRA for EXPORT: For base machine dismantling and placing on two (2)  heavy duty wooden platform skids, vacuum-wrapped, including boxing of accessories, transport/freight to export  packer’s facility, including export packing/preserving for  sea-worthy transport into 40-Ft. “High Cube” ocean  cargo container, with delivery C.I.F WILL ADVISE … ( upon request ) * * * * * NOTE: The aforementioned description and list of accessory equipment is correct and accurate to the best of our knowledge. However, it is not binding in any regard, as we reserve the right to change and/or alter same without prior notice. Consequently, the buyer is responsible for confirming same upon physical inspection and inventory of the machine and all related accessory equipment. Contact Rich Piselli to set up an under power inspection.