AGIE AGIECUT SPRINT 70 CNC EDM
Agie Model AgieCut Sprint 70 CNC Wire Electrical Discharge Machine With: Agiematic D CNC Control
AGIE AGIETRON ADVANCE
Agie AGIETRON Advance Sinker EDM, 1998
AGIE AGIETRON SPIRIT 2
Agie Spirit 2 CNC Sinker EDM, 2005, Rack ATC 5-10 Positions C-Axis System 3R Macro Chuck Short set-up times Simple Data Input Great Application Spectrum High Removal Rate
AGIE AGIETRON SPIRIT 3
Agie Spirit 3 Sinker EDM, 2007 Excellent Condition. Under 5,000 Burn Hours Rack ATC 5-10 Positions C-Axis System 3R Macro Chuck
AGIE MONDO
33.8” X 25.5” X 12.4” Sinker EDM with Agie Futura V IPM CNC Control, C - Axis (4th Axis), 4 - Position Automatic Toolchanger, Chuck Mounted on Ram and Remcor Chiller.
AGIE MONDO 2
Agie Mondo 2 Sinker EDM
AGIECHARMILLES AC PROGRESS V4 CNC WIRE EDM
Rated 47" Sq/hr - AgieVision Control, Version 5 - Windows Operating System
AGIECHARMILLES SP1 DIE SINK EDM
1 - AgieCharmilles SP1 Die Sink EDM Year of Mfg: 2010 Serial #: 164-002 This unit is on one large skid, roughly 7'9" x 7'9" x 8', weighing approximately 6,000 LBS. - Offered by K. B. Industries,...
CHARMILLES FORM 350SΜ
AGIECHARMILLES FORM 350Sµ - 2008 Die Sinking EDM machine AGIECHARMILLES FORM 350Sµ - 2008 Die Sinking EDM machine https://remiswiss.com/product/agiecharmilles-robofo...
AGIECHARMILLES +GF+ FORM 550S
AGIECHARMILLES FORM 550S - 2008 + TOOLS CHANGER - EDM Die sinking machine AGIECHARMILLES FORM 550S - 2008 + TOOLS CHANGER https://remiswiss.com/product/agiecharmille...
AGIECHARMILLES +GF+ FORM 550S
AGIECHARMILLES FORM 550S - 2008 + ROBOT PARTNER 3R - EDM Die sinking machine AGIECHARMILLES FORM 550S - 2008 + ROBOT PARTNER 3R https://remiswiss.com/product/charmil...
BELMONT MX-166W
Belmont MX-166W CNC Sinker EDM, 2014 – 200 Amp, 8 ATC, 51″ x 28″ Table, C-Axis
BROTHER HS-50A CNC WIRE TYPE EDM
5 Axis, Wire Type, Under 7000 Hours, 23" x 18" Table
CHARMILLES FO-350
Super nice Charmilles Sinker EDM. Was just taken off of power due to routine updates. It is in great condition! To the best of our knowledge, all details listed below are deemed correct. It is the ...
CHARMILLES FORM 20
Item #: BV2744 CHARMILLES FORM 20 DIE-SINKER EDM EQUIPPED WITH: EQUIPPED WITH: - AGE: 1999 - SERIAL 200423 - X,Y - 11.8" , 9.8" - TANK: - TRANSFORMER PERM MAG CHUCKS - HEIDENHAIN 3 AXIS DRO PRI...
CHARMILLES ROBOFORM 4000 RAM SINKER EDM
34.6"X22" Table Area, 44"X31"X17"
CHEVALIER ZPNC-251
Chevalier Model ZPNC-251 Ram EDM, 50 Amp, Programmable Z Axis, 11 3/16" X 7 7/8" X 5 7/8" Travels........................................$6,950.00 F.O.B. Dayton, Ohio Contact : Larry 937 -477-...
CHMER CM-434Z RAM SINKER EDM
Chmer Orbit Cut COC-200A, Erowa EDM Tooling
ELOX 8-2012
ELOX AGIE AMERITRON 50, FUTURA II POWER SUPPLY,
Elox AGIE AMERITRON 50, FUTURA II POWER SUPPLY, RAM-TYPE EDM, 3-AXIS DRO, CNC "Z" AXIS', SYSTEM 3R ORBITOR
ELOX AGIE FUTURA V 2PM
Elox Agie Futura V 2PM Sinker EDM, 1996
HANSVEDT BENCHMAN
Pulse 201E Power supply
HANSVEDT CS-1, 1996, WITH SYSTEM 3R ORBICUT CNC
6" Y Axis 8" X Axis Hansvedt CS-1, 1996, WITH SYSTEM 3R ORBICUT CNC RAM-TYPE EDM, H201 POWER SUPPLY, 9" X 15" TABLE,
HANSVEDT LEADMAN 502
Very Nice Manual EDM, Well equipped. Inspect under power in our warehouse. SEE VIDEO of Machine Burning
HANSVEDT MS-1
Hansvedt MS-1 Benchman /M-Pulse 1025 EDM Sinker, 1998 – Available Immediately!
HANSVEDT WORKMAN
Hansvedt WORKMAN, 1994, RAM-TYPE EDM
HARDINGE HANSVEDT
8” X 6” X 8” Sinker EDM with M-Pulse Power Supply
HUEY LONG HM-30
Used HUEY LONG (M.I.T) NC-Tester edm-dim-sinkking edm Model: HM-30 Our website: https://www.ryokuta.com/en/product-series/nc-tester-edm-die-sinkking-edm
MAKINO EDNC
78.74” X 27.55” X 23.62” Sinker EDM with Makino MGH5 CNC Control and EROWA Robot System with Makino MG45 Control.
MAKINO MGB-30
MAKINO U53 CNC WIRE TYPE EDM
Under Power, Excellent, Immediate Availability
MITSUBISHI DWC90H CNC WIRE TYPE EDM
Auto Thread, Fine Finish (2) Available
MITSUBISHI EDM DWC90H CNC WIRE TYPE EDM
1993 Mitsubishi DWC90H CNC EDM. Pre-owned, 16"x20.1" table, 11"x9"x6" travel. Reliable precision for complex tasks. Ideal for diverse machining needs. This 1993 EDM is in good working condition, th...
MITSUBISHI FA10SM 5 AXIS WIRE TYPE EDM
5 Axis, Auto Wire Threader, Mitsubishi 64 Bit CNC Control