Looking: CNC Gantry or Bridgemill 3-axis, 10k rpm, 230" or more on x
3" centers on rollers. Side rails are a plus. End stop required. 6-10 sections needed. All must be same manufacturer.
Pipe dies for my R3 Roundo
3"-6" CNC MANDREL BENDER FOR STAINLESS PIPE LATE MODEL
Looking for a 2D wire bender for 10 gauge (.101" or .258 mm) wire. Need U.S. based support and parts.
Looking for a Threading Systems TS56R, the closer to TX the better.
Plasma Table CNC 5' x 10' 1/2" Capacity height Control slag removal etc
Hollow spindle lathe. Approximately 32” x 180” with front and rear chucks. Can be larger
Prefer, DMG, Mazak, OKK no older than 10 years
CNC PRESS BRAKE LATE MODEL IN NEED OF 4-7 AXIS CNC PRESS BRAKE 200 TON - 300 TON X 12' OR SIMILAR
3" X 3" X 3/8" ANGLE ROLL LATE mODEL
We are looking for a very large rotary tilting table with a load capacity of up to 120 tons. The most important factors are the load capacity of 100-150 tons and that the table can be swivelled 180°.
Looking for a steady rest for a Milltronics ML20 lathe. At least 6" capacity, preferably larger.
Used fiber laser machines, used punch press, used press brakes,
wa whitney 791-000x 12 1/2" throat portable press any condition
Hydraulic Plate Bending Roll 5/8" to 1" x 6'. NOTE: 6' to 8' is maximum length accepted. 3 or 4 roll machine. MUST BE NOT OLDER THAN 10 YEARS
any wa whitney older power unit, even if needs updated or repair
Wotan B150K 6” Dia. Spindle NMTB 50 Taper X-travel is 208” – need 180” min. Y-travel is 88” – need 72” min. Z-travel is 36” (spindle in-out) – need 28”” min. W-Travel…
Looking for 2003+ CNC OD /ID grinder Parts, 16” or smaller diam would work Prefers Kellenberger , Okamoto etc Probing is a plus. ie: Kellenberger with 2 OD & 1 ID heads
5" Floor type manual boring mill, 15' travel
700 Ton Spotting Press, Roll Out Bolster, Tilting Platen
used pc- 800 control off of 630 or 650 wa whitney
VtL cnc 1000 mm w/ live tooling
Apron brake
Tube bender would be mostly for 1 3/8” to 2 7/8” dia tubing.
5" - 6" Spindle Floor Type HBM, X-Axis under 240", Y-Axis - 96" Max, Manual machine preferred
Need a lathe headstock that can swing approx. 55"
Looking for a good 3 axis lathe with Fanuc control, tailstock and either a 8" or 10" chuck. Live milling is an absolute, but don't need Y axis to push the price up. Doosan, Mori or Mazak would work.
Seeking 1st low-budget CNC mill to Hayward CA 94545. Minimum specs. working, 3axis, 2.5HP, 4000RPM, power-draw-bar or QC. Knee or bed mill, year-2000 or more modern. Must allow G-code input or DNC, cannot be conversational only. Must have…
wa whitney 650 duplicator with pc-800 control
We need a machine that can do single GF15 PA6 or GF15 PBT parts with simple geometry, in shot sizes of up to 80G, and can support thin parts with a footprint of at least 150x150mm. Semi-automatic or automatic cycles preferred but not a must.
Large Bridge-Style Jig Grinder
wa whitney portables any model, needing repair
Looking for a C-Frame Press for crimping
Machine to be in very good condition and in the USA
100-150 Ton Brake Press 8' wide with updated controller DT66T or ETS3000 or similar.
Looking for a early to mid 2000's vintage Citizen L20 Type VII or Type VIII with barfeed.
Mazak QT10, QT6, QT200 or QT20 with 6" or 8" chuck, chucker are ok and actually preferred. Either Mazatrol Tplus control or Mazatrol Fusion 640T control. Budget buyer
engine lathe with 6 " or bigger chuck
whole milk separator, westfalia msd 160 with control panel. also need a standardization system for this separator.
Looking for a 6'x12' Waterjet with a 100 hp and 94k psi pump
Need a newer 200+ Ton Straight side single crank press, 33.5" FB x 30.5" LR, 12" min SH, 6" min stroke
wa whitney older style, needing updates power units (5000 psi )
Highlight Revolver Model 7020 Stretch Wrapper
Looking for oilfield lathes with Fanuc Controls. Tailstock not needed. Need 7" bar capacity.
Looking: 2-Axis turning center 36" length, Fanuc and west coast preferred.
Need this grinder for lathe blader
I'm looking for a ACCURPRESS #710012 #Press Brakes, but am open to other manufacturers and models.
I'm looking for a ACCURPRESS #7606 #Press Brakes, but am open to other manufacturers and models.
I'm looking for a ACCURPRESS #ACCELL 515012 #Press Brakes, but am open to other manufacturers and models.