在庫No.:PM-1340GT-PEP With Stand, SINGLE PHASE
¥593,999.41 JPY


スイング:330.2 mm
センター:1,016 mm
スピンドル ボア:39.98 mm
パワー:1.5 kW
回転数:1600 rpm
スイング オーバー クロス スライド:177.8 mm

Give us a call at 412-787-2876 or see our web site

Type Geared Head
Model PM-1340GT
Max. Swing over bed 13"
Max. Swing over cross slide 6-1/2"
Max. Swing in gap 19-1/8"
Center Height 6.5"
Spindle Center Line Distance from Floor Approx. 46”
Max. Distance Between Centers 40"
Width of Bed 7-1/2”
Bed Height 11.5”
Spindle Bore 1-9/16”
Spindle Taper, Internal MT #5
Spindle Mounting System Cam Lock, D1-4
Spindle Speeds 90-1600 RPM, 12 Steps
Bed Length 63-3/4"
Lead Screw Diameter / Pitch 7/8” / 8 TPI
Feed Rod Diameter 3/4”
Inch Thread Cutting Range 4-112 TPI, 40 Different Threads
Metric Thread Cutting Range .25-7.5mm Pitch, 24 Different Threads
Longitudinal Feed Range (Left and Right) .002-.02 Inches Per Revolution
Cross Feed Range (In and Out) .001-.01 Inches Per Revolution
Spindle Length through headstock, Protruding End to D1-4
Chuck Mounting face
Approx. 13-3/4”
Spindle Length through headstock, Protruding End to 3 Jaw
Chuck face
Approx. 17-1/4”
Cross Slide Travel 6-3/4”
Compound Travel 3-1/2”
Tail Stock Quill Diameter / Travel / Taper 1-9/16” / 4” / MT#3
Main Motor Horsepower 2 HP
Voltage / Phase/ Amps 220 Volt, 1 Phase / 12 Amps Max.
Optional 220 Volt, 3 Phase / 9 Amps Max
Machine Dimensions, Assembled with stand 52”H x 29”W x 70”L
Machine Weight, without stand 1000 LBS
Machine Weight, With Steel Stand 1310 LBS


Give us a call at 412-787-2876 or see our web site

Highest Quality Lathe, Made in TAIWAN
• Large 1-9/16” Spindle Bore clear through spindle for through-headstock work
• Short Spindle Length, only 13-3/4", perfect for gunsmithing work - great lathe for gun or gunsmith work
• Extra thick spindle wall for extra rigidity, almost double when compared with most other
machines in this size
• Power feed on Carriage, and Cross Slide, both left and right, and in and out, for both turning
and facing operations with automatic feed. Allows for the best surface finish in all directions.
• Induction Hardened and Precision Ground Bed Ways to resist wear and give a long service life
• All shafts in headstock hardened and ground along with gears which are precision ground, set in
with a close tolerance fit, which leads to longer life and quiet running when compared with
other geared head lathes
• Inch AND Metric thread cutting ability is a standard feature, NO CHANGE GEARS for any
inch thread or feed rate, only change gears required are for Metric threads
• 4” Travel Thread Dial, 32 tooth gear on thread dial, 8 TPI Main Leadscrew for easier threading
using the half nut / thread dial
• Large diameter, extra thick wall tail stock quill for more rigid and accurate tail stock operations,
Locking Tang in tail stock is provided
• Removable Gap for larger diameter work when needed
• High quality electronics used throughout machine, very reliable contactors, motors, etc.
• Slip Clutch is standard on feed rod, to help prevent overloading damage of feeds and allow the
use of a solid carriage stop for repetitive work
• Precision Tapered Roller Bearings used in spindle, for the ultimate in long life, high precision,
and best surface finishes. Guaranteed Run Out +/- .0001" for ultimate precision
• True INCH PITCH main lead screw, cross feed, and compound lead screws make it easy to use
for the INCH measurement System, yet still has the Metric readings on dials for the ultimate in
versatility for any job that may come about
• Splash oil bath lubrication in Headstock, and Apron, for efficient lubrication, and long life, yet
simple and reliable, and does not require any filter changes or pump maintenance as with oil
pump lubrication systems. Also no risk of losing oil flow to expensive parts as there can be with
pump lubricated systems
• Only Extremely High Precision Spindle Bearings are used, FAG, NSK, NTN, or NACHI
5 Year Warranty



の詳細について表示するには、 PRECISION MATTHEWS PM-1340GTレビュー、ブランド情報、写真、ビデオ、および多くを含むが、 ここをクリック