• 1994 Current EDM ST300 Refurbished Hole Driller #1384
  • 1994 Current EDM ST300 Refurbished Hole Driller #1384
  • 1994 Current EDM ST300 Refurbished Hole Driller #1384
見る

EDM ホールドリラーCURRENT EDM ST300

アメリカ合衆国

概要

ブランド
モデル
ID
459213
1994
場所
アメリカ合衆国
帰りの方針
現状のまま
在庫No.
1384
詳細
Current EDM manufactures the finest hole drillers in the world. Used in applications such as aerospace, medical, aircraft and automotive. The ST300 accurately drills holes in nearly any electrically conductive material, at high rates, on angles, curved surfaces, and through threads. This machine is ideal for drilling "start holes" for wire EDM, gas escape holes in molds, and production holes in hardened materials where conventional drilling is difficult. Its rugged construction makes it suitable for tool room and production applications. STANDARD MACHINE FEATURES * Utilize electrode diameters from 0.004-0.250in. Drill to depths up to 300 times hole diameter. * Rigid CAST BRIDGE design for optimum machining accuracy and low maintenance. X + Y axis slides are located above the drilling area away from dielectric fluid sprays. * CLOSED -LOOP, linear scale feedback for X and Y axis. Direct-to-shaft encoder feedback for Z-Axis. High-precision, re-circulating ball way slides used on X, Y and Z axis. * 8 x 12in table travel and 12in Z-Axis servo stroke. X, Y and Z axis digital read-outs are displayed in inch or metric coordinates at a resolution of 0.0002in (0.005mm). * PROGRAMMABLE DRILLING DEPTH SET AND RETRACT. The Controller automatically keeps track of the drilling depth even if machining is interrupted. Variable retract height input is necessary to ensure the electrode will not retract out of the guide. * Precision lapped GRANITE WORKTABLE. Exceptional flatness and electrical insulation enhance machining performance. * AUTO MODE and CYCLE features automate drilling when the M-Function interface cable is connected to a rotary or indexing table. Up to 998 drilling cycles, or continuous operation, can be programmed at the Controller. * "SOFT START" feature virtually eliminates entry point burr formation. Power settings are automatically lowered upon initial contact and then gradually increased to full power. * INITIAL ZERO SET to drill consistently to a set depth, the Z-axis coordinate display automatically resets to zero upon initial drilling contact with the workpiece. Initial Zero Set override is also possible. * One-piece CENTERLESS GROUND SPINDLE. To facilitate electrode changing,the spindle can rotate in the clock-wise or counter clock-wise direction. The electrode drill chuck is installed or removed from the spindle with the push of a button. * CONTROLLER The Controller unit is mounted on a swing-away arm for easy positioning. A membrane keypad is utilized to minimize maintenance. * Machine system designed to drill with WATER DIELECTRIC fluid. * Four separate power supply circuit breakers to protect and extend the life of critical components. * Audio signal EDGE FINDING circuitry for workpiece referencing and contact sensing.
スペック
メトリックに仕様を変換します
ホール径 (最小)0"
ホール径 (最大)0.26"
作業-W12"
作業-L12"
X12"
Y8"
Z12"
大きさ24" x 28" x 70"
重量800 lbs (364 Kg)

スペックシート

* Current EDM Controller w/XYZ DRO's * Granite Worktable with Stainless Rails * Add-on Tank for Submerged Machining * Three-Piston Electric Pump for Consistent High-Pressure Flush * 57 Peak Amp Power Supply * All Available Manuals and Accesories ** Filtration system available at additional cost. This machine can also just draw water from a wire EDM.
売り手について

このタイプのリストを参照してください

thumb

DJ 1612

EDM ホールドリラー

新しい在庫がある | Michigan, アメリカ合衆国
thumb

SODICK K1C

EDM ホールドリラー

使用 - 優れました | 2004 | Quebec, カナダ
$8,900.00 USD
thumb

CHMER H32C

EDM ホールドリラー

使用 - リビルト | 2005 | Illinois, アメリカ合衆国
thumb

BELMONT MAXICUT S-36

EDM ホールドリラー

2006 | Ohio, アメリカ合衆国
すべてを表示

このブランドのためのより多くのリストを参照してください

thumb

CURRENT EDM CT-500F W/ ELECTRODE CHANGER

EDM ホールドリラー

1998 | Arizona, アメリカ合衆国
thumb

CURRENT EDM CT300

EDM ホールドリラー

1999 | アメリカ合衆国
thumb

CURRENT EDM CT300

EDM ホールドリラー

使用 - リビルト | 2000 | アメリカ合衆国
thumb

CURRENT EDM RT6050

EDM ホールドリラー

中古品 - 良いです | 2012 | アメリカ合衆国
すべてを表示