GANESH VFM-4024수직 머시닝 센터

형태:수직 머시닝 센터
조건:새로운에서 주식
제어:CNC (Mitsubishi M720 CNC Control)
판매자:판매자가 누군지보기 ...
₩114,123,586.50 KRW


X:1,000 mm
Y:599.9 mm
Z:561.8 mm
동력:22.4 kW
분당 회전속도:12000 rpm
# ATC:24
테이블 W:499.9 mm
테이블-L:1,100 mm
치수:LXWXH 121” x 91” x 101”
무게:13,228 lbs
제어반:CNC (Mitsubishi M720 CNC Control)

X-Travel 39.37” 1,000mm
Y-Travel 23. 62” 600mm
Z-Travel 22. 12” 562mm
Spindle Nose to Table Surface 5.1”– 27.56” 130 – 700mm
Spindle Center to Z-axis covers 20.35” 517mm (throat dimension)

Table Size (LxW) 43.3” x 19.68” 1,100mm X 500mm
T-slots - 5 total 0.709” slot width 18 mm X 100mm
Max. Table Load (evenly distributed) 1,541 lbs 700kgs

Spindle Motor – 15,000 rpm 1:1 ratio 30 HP Peak (25kw) 20-HP (10-minute duty rating)
Spindle Speed – Inline Direct-Drive 12,000rpm (opt 24,000rpm Integral Spindle)
Spindle Torque 115 ft-lb @ 1,500 rpm 70 Nm @ 30-min. duty rating
Tool Type CAT #40 Taper (BT #40 optional)
Spindle Taper Material / Hardness SCM415 / HRC58-62
Retention System / Holding Capability Bellville Spring Stack 1650-1760 lbs
Spindle Orientation By sensor
Spindle Runout 0.000040 T.I.R.
Spindle Bearing Front 110mm NSK 70BNR 10 x 2, P4 class-7 bearings
Spindle Bearing Rear 110mm NSK 70BNR 10 x 2, P4 class-7 bearings

Rapid Traverse X and Y 1,417 ipm 36m / minute
Rapid Traverse Z 945 ipm 24m / minute
Cutting Feedrate 0.04 - 810 ipm
Axis Drive Motor Power – X, Y 4-HP (3kw nominal) Mitsubishi HF303S-A48
Axis Drive Motor Power – X, Y 5-HP (3.5kw nominal) Mitsubishi HF354BS-A48 w/brake
Ballscrews – X, Y, Z 40mm ballscrews with 12mm pitch
Maximum Thrust Force 4408 lbs 2,000 kg
Constant Thrust Force 2204 lbs 1000kg
Linear Positioning Accuracy (Renishaw) 0.0002”/12” 0.005/300 mm
Linear Positioning Repeatability (Renishaw) 0.0001” 0.0025 mm

Tool Capacity – 24+1 or 30+1 24 or 30-Tool Twin-Arm (40-tool changer optional)
Tool Shank CAT#40 Taper (BT#40 optional)
Tool Change Time (average) 1.7-seconds tool-to-tool, 2.1-seconds chip-to-chip
Maximum Tool Diameter / w/adjacent tool 5.90” / 3.15” 150mm / 80mm
Maximum Tool Length 11.81” 300mm
Maximum Tool Weight 15 lbs. 7kg
Tool Selection / Tool Access Random access / Bi-directional

Air Service Requirements 85 psi @ 5-scfm 7 Kg/cm2
Coolant Capacity 100 gallons 367 liters
Connected load electrical requirement 35kva, 75-amps 208-220vac, 60-Hz
Floor space requirements recommended 115” x 99” x 111” 290x250x280cm
Shipping dimensions (L x W x H) 121” x 91” x 101” 306x231x256cm
Machine Weight 13,228 pounds 6,000 kg
Warranty – 1-year machine warranty 3-year Mitsubishi control, motor & drives warranty


High Speed CNC Machining Center, VMC with Rugged Cross Linear Ways. Ganesh VFM - 4024 4th & 5th Axis Ready 12,000 RPM standard. Rugged Cross Linear Ways, 1,417 Inch Per Minute Rapids.
4th and 5th Axis Wiring Standard
1,417 inch per minute rapids
12,000 RPM Direct Drive Spindle Standard
Powerful Fanuc or Mitsubishi CNC Controls
Rugged Cross-Linear Ways
Double Anchored Pre-Tensioned Ball Screws
MPG Handwheel Standard
1.7 Seconds High Speed Arm Type ATC
Rugged Meehanite Casting
1,000 PSI Thru-The Spindle Coolant Ready


이 모델에 대해 더욱

더많은 정보를 보기 위해서는 GANESH VFM-4024, 리뷰포함, 브랜드 정보, 사진, 비디오 등, 여기를 클릭하세요..