MESSER METAL MASTER II플라즈마 절단기

ID#:359267
상표:MESSER
모델:METAL MASTER II
형태:플라즈마 절단기
년도:2000
제어:CNC (MG Pilot)
판매자:판매자가 누군지보기 ...
위치:Ontario
캐나다
Stock # :3133
가격:

투기

Lower:29
컷 -폭:1,829 mm
절단 길이:3,048 mm
플라즈마 전원:100 a
Upper:49
#플라즈마 토치:1
절단속도:1000 inpm
제어반:CNC (MG Pilot)

POWER CAP. 100 AMP
STANDARD CUTTING SURFACE 6' X 10'
CUTTING CAPACITY UP TO 1/2" CARBON STEEL
CUTTING CAPACITY, CARBON, STAINLESS STEEL
& ALUMINUM FROM 26 GAUGE TO 1/2"
POSITIONING SPEED UP TO 1000 IPM

SERVO DRIVES W/ PLANETARY GEARBOXES WITH 5 ARC/MINUTES OF BACKLASH
SINGLE SIDE DRIVE IN "X" AXIS WITH RIGID STRUCTURE, PROVIDES BEST
METHOD FOR DRIVE PERFORMANCE
EXTRUDED ALUMINUM BEAM WITH DELTA DESIGN
PRECISION PLASMA SYSTEM CAPACITY
RSVP 421 HEIGHT CONTROL PROVIDES BEST CUT QUALITY
WITH VIRTUALLY NO DROSS
STATE OF THE ART DRIVES WITH SYNCHRONISATION OFFER THE BEST OPERATION
HIGHER ACCELARATION/DECELARATION CAPABILITIES
AND LOWER INERTIA

Equipped With:

* HYPOTHERM HD3070 PLASMA SYSTEM W/PATENTED HYFLOW VORTEX NOZZLE WHICH STABILIZES THE PLASMA COLUMN, PRODUCING EXCEPTIONAL CUT EDGE QUALITY, & FORCES THE ARC ATTACHMENT POINT TO BE DEAD CENTER ON THE ELECTRODE FOR LONGER PARTS LIFE WITHOUT SACRIFICING CUT QUALITY( 1/2" PRODUCTION CAPACITY )
* PLASMA SM-1000 "HIGH SPEED"
QSE QUICK DUCT SOFTWARE
* DOWN DRAFT TABLE WITH TUCKED RAIL DESIGN INCLUDING CENTER DUCT & DAMPERS
* TORCH COLLISION PROTECTION
* MG PILOT CNC SYSTEM - PC BASE:
- TRUE PC ( PENTIUM ) BASED CNC
- 10.4" COLOR DISPLAY
- WINDOWS 95
- 1 GIGABYTE STORAGE CAPACITY
- REAL-TIME GRAPHIC DISPLAY
- PRE-PROGRAMMED SHAPE LIBRARY UP TO 200 POSSIBLE SHAPES
- MULTI-TASKING
- GRAPHIC PREVIEW OF PROGRAMS IN HOST LIBRARY
- KERF-ON-THE-FLY
- DUAL FEED RATE OVER RIDE FOR TWO PLASMA
- LOST POWER RECOVERY
- DUAL CONSUMABLES MONITORING GRAPHICS
- HIGH SPEED SERIAL COM UP TO 115 KBAUD
* MACHINE DRIVE SYSTEM USES A 125W PERMANENT MAGNET MOTOR DRIVING A RACK & PINION, THRU A LOW BACKLASH PLANETARY GEAR HEAD CONTROLLED BY A PULSE WIDTH MODULATED AMPLIFIER

Indepth Description:

THE METALMASTER II IS A HIGH SPEED PLASMA ARC CUTTING SYSTEM FOR CUTTING CARBON, STAINLESS STEEL & ALUMINUM FROM 26 GAUGE TO 1/2" THICK, IT IS A HIGH DEFINITION PLASMA SYSTEM WHICH GIVES EXCEPTIONAL EDGE QUALITY, COUPLED WITH THE NEW MG PILOT CNC CONTROL, THE INTEGRAL TRACK BASE, AND EXHAUSTED CUTTING TABLE WILL ALLOW YOU TO PRODUCE HIGH QUALITY PARTS IN LESS TIME. THE MACHINE RIDES ON TRACK MOUNTED TO A ONE PIECE BASE STRUCTURE, THIS KEEPS THE TRACK IN PERFECT ALIGNMENT, THE BASE ALSO SUPPORTS THE FULLY ZONED & DUCTED CUTTING TABLE. THE STANDARD CUTTING SURFACE IS 6 X 10 FEET, BUT CAN EASILY BE EXTENDED IN 5' INCREMENTS TO A TOTAL OF 25'.

이 모델에 대해 더욱

더많은 정보를 보기 위해서는 MESSER Metal Master II, 리뷰포함, 브랜드 정보, 사진, 비디오 등, 여기를 클릭하세요..