GANESH GT-26160갭 선반

ID#:363251
상표:GANESH
모델:GT-26160
형태:갭 선반
조건:새로운에서 주식
년도:2017
위치:California
미국
가격:
$39,995.00 USD

투기

Lower:23
스윙:26 "
갭 스윙:33.38 "
중심:160 "
스핀들 보어:4.125 "
Upper:43
동력:15 hp
분당 회전속도:1200 rpm
테이퍼:MT-5

Capacity & Dimensions-
Swing over Bed 26” (660mm)
Center height 13” (330mm)
Swing over Cross Slide 18-1/16” (460mm)
Swing thru Gap 33-1/4” (845mm)
Length of Gap in front of faceplate, D1-11 6-1/2” (165mm)
Bed width 16-1/8” (400mm)
Spindle-
Spindle Motor Horsepower 15-HP 3-Ph 12kw
Spindle speeds – 12-speeds from 15 – 1200 rpm) (High & Low speed range)
Spindle Bore 4-1/8” (105mm)
Spindle Nose D1-11 Camlock (A1-11 optional)
Spindle taper in spindle nose MT-8 Morse Taper # 8
Spindle taper reduction sleeve provided MT-5 MT-8 to MT-5
Spindle Max weight capacity (Chuck only) 660 lbs (300kgs)
Spindle Max weight capacity (Chuck and Tailstock) 1,650 lbs (750kgs)
Spindle Max weight capacity (Chuck, Steady Rest and Tailstock) 3,300 lbs (1,500kgs)
Carriage -
Cross slide travel 14.96” (380mm)
Cross slide width 7-3/32” (180mm)
Cross slide lead screw pitch .200”/rev.
Cross slide resolution per division 0.001” (on diameters)
Carriage lead screw diameter 1-1/2” (38mm)
Carriage lead screw pitch 4 TPI (6mm pitch)
Compound- Four T-nut lock-down bolts on compound cross-slide base
Compound top slide travel 10” (255mm)
Compound top slide width 4-11/32” (110mm)
Cutting tool height maximum 1.0” x 1.0” 25mm x 25mm
Tailstock- (2-speed quill advance) Engraved with inch / metric quill graduations
Quill diameter 2-15/16” (75mm)
Quill stroke 6-5/16” (160mm)
Quill taper MT-5 Morse Taper # 5
Tailstock body set-over adjustment ± ½” (± 13mm)
Thread Cutting-
Thread cutting range – 60 inch pitches 2 – 112 TPI 2 – 112 TPI
Thread cutting range – 60 metric pitches 0.2 – 14mm 0.2 – 14mm
Thread cutting range – 50 diametral pitches 4 – 112 D.P. 4 – 112 D.P.
Thread cutting range – 50 module pitches 0.2 – 7 M.P. 0.2 – 7 M.P.
Feeds- (with clutched feed shaft for safety)
Feeds – longitudinal - 50 feeds 0.0014” – 0.0387”/rev. 0.037 – 1.04mm/rev.
Feeds – cross - 50 feeds 0.0007” – 0.01935”/rev. 0.0185” – 0.52mm/rev.
Power Requirements 220 vac, 3-Phase, 42-amps (440vac optional)
Coolant System 1/8-HP Pump Motor, 5 gallon (20L) tank capacity

세부내역

GANESH GTW-26 Precision Lathe Series 26” Swing, 40” – 160” between centers, Electric Motor Driven Rapid Traverse Feeds
15-HP Spindle Motor
Spindle Speeds from 15 – 1200 RPM
12-Spindle Speed Gear-Ranges for High-Torque
D1-11 Camlock Spindle (A1-11 optional)
4-1/8” Spindle Bore
Rapid Traverse Axis Feeds
Efficient 2-Speed Quill Advance
33-1/4” Swing in 6.5” Wide Gap

다운로드

이 모델에 대해 더욱

더많은 정보를 보기 위해서는 GANESH GT-26160, 리뷰포함, 브랜드 정보, 사진, 비디오 등, 여기를 클릭하세요..